California Air Tools 4610A-220V Instruction Manual download pdf (Page 13)

Sand Blasting

Hook Up Guide

MicroEtcher & MicroProphy Quick Disconnects

Chairside

The barbed tee is

installed directly in

the incoming air line,

either in the cart or

in the junction box.

Cut the air line to

install the tee.

Quick Disconnect Kit

Male & female with barbed

tee for 1/4” air line.*

PN 44000

Initial Hook Up Kit

Chairside

As above.

Female Only

Quick disconnect with barb

tee for 1/4” air line.*

PN 44010

Secondary Outlet Kits

Laboratory Stopcock

Slip tubing end over

the stopcock.

Female Only

Quick disconnect.

PN 44017

Handpiece Line

Screw on the

adapter. Adjust the

air pressure.

4-5 Hole Handpiece

Adapter

PN 44075

Male Only Quick Disconnect

PN 44020

Quick Disconnect Installa tion: The

MicroEtcher and Microprophy are

designed to operate over a pressure

range of 50 to 120 psi (3.4 - 8.3 bars).

Either can be installed using one of

three options: a Quick Disconnect

Kit, a Laboratory Quick Disconnect

or a Handpiece Adapter. A review of

the following information will help you

decide which adapter is best suited to

your needs. Higher pressures will lead to

superior performance.

Option 1

Quick Disconnect Kit: The Quick

Disconnect Kit is designed to be used in

the operatory for chairside sandblasting.

The kit consists of a female disconnect, a

tee which is spliced into the line coming

from the compressor before the pressure

regulator (i.e., junction box or cart),

and a separate male connection. The

male connection is installed on the end

of the MicroEtcher tubing. A tee (with

the female connection) may be installed

in more than one operatory so that the

MicroEtcher with its male disconnect may

be used in each room.

Option 2

Lab Quick Disconnect Kit: In the

laboratory there is generally an air line

with 80 - 100 psi (5.5 - 6.9 bars) pressure.

If an air jet (stopcock) is present, the

Lab Quick Disconnect with its female

disconnect is designed to be permanently

installed on it. The male disconnect is

installed on the end of the MicroEtcher

tubing. With a female Quick Disconnect

installed in the lab, and also in the

operatory, the MicroEtcher can be used in

both places.

Option 3

Handpiece Adapter: If there is an extra

handpiece line in the operatory which can

be adjusted to 50 psi or more (3.4 bars),

the handpiece adapter can be installed on

the end of the MicroEtcher tubing.

* Special hook up connections, i.e., tees, plastic and copper lines are also available.

Contact our Customer Service Department for assistance.

Female

Barbed Tee

Male

Female

Screw on Outlet

Slip Over Stopcock

S

Scr

ew

Female

Sl

i

p O

ver

S

t

opc

ock

y

Description

Diagram

Air Source

50 - 120 Psi

(3.5 - 8 Bars)

Female

Barbed Tee

Barbed Te

e

Handpiece Adapter

Kavo Style

Kavo Adapter

PN 201431-00

Screw on Outlet

Scr

ew

Laboratory Stopcock

Slip tubing end over

the stopcock.

Female & Male

Quick disconnect.

PN 44007

Female Slip Over Stopcock

Fe

m

ale

Sl

i

p

O

ver

S

t

o

Male

13

Call 800/827-7940 or visit danvillematerials.com

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 51 52

Comments to this Manuals

No comments